Chipped front pane of glass, panic time?

Darkxness

New Member
View Badges
Joined
Jun 1, 2023
Messages
10
Reaction score
9
Location
Ireland
Rating - 0%
0   0   0
Hey there,

Was doing a water change and must have somehow chipped the front glass of my AquaNano 60.

The chip is on the outside and at the deepest part seems to be around half of the depth of the glass deep.

There doesn't seem to be any runners/cracks but it is right the the top of the glass.

I have superglued the chip back in.

Is this safe or should I drain some water and replace this weekend?

Thanks in advance

photo_2024-04-13_19-07-21 (2).jpg photo_2024-04-13_19-07-21.jpg photo_2024-04-13_19-09-15.jpg
 

GlassMunky

2500 Club Member
View Badges
Joined
Jan 30, 2014
Messages
2,949
Reaction score
3,845
Location
NJ-Philly Burbs
Rating - 0%
0   0   0
Hey there,

Was doing a water change and must have somehow chipped the front glass of my AquaNano 60.

The chip is on the outside and at the deepest part seems to be around half of the depth of the glass deep.

There doesn't seem to be any runners/cracks but it is right the the top of the glass.

I have superglued the chip back in.

Is this safe or should I drain some water and replace this weekend?

Thanks in advance

photo_2024-04-13_19-07-21 (2).jpg photo_2024-04-13_19-07-21.jpg photo_2024-04-13_19-09-15.jpg
That’s at the top of the tank above the water line?
It’s not anywhere near the seams….

I’d think it should be fine and doesn’t risk any kind of failure.
But def be sure to monitor it and make sure it doesn’t spread in case there’s some small cracks you can’t see
 
OP
OP
Darkxness

Darkxness

New Member
View Badges
Joined
Jun 1, 2023
Messages
10
Reaction score
9
Location
Ireland
Rating - 0%
0   0   0
That’s at the top of the tank above the water line?
It’s not anywhere near the seams….

I’d think it should be fine and doesn’t risk any kind of failure.
But def be sure to monitor it and make sure it doesn’t spread in case there’s some small cracks you can’t see
Yep right at the top of the tank.
There is no seams on this tank except the back corners, fronts are rounded, it's a single piece for the front and two sides.

I'll keep an eye on it every day, thanks for the reply!
 

braaap

Well-Known Member
View Badges
Joined
Jul 16, 2015
Messages
942
Reaction score
834
Location
Montana
Rating - 100%
3   0   0
Personally I wouldn't be overly worried. It could cause it to crack straight down from there and split on the next contact or stress. So if you can afford to replace it I would. But I wouldn't IMMEDIATELY do it.
 
OP
OP
Darkxness

Darkxness

New Member
View Badges
Joined
Jun 1, 2023
Messages
10
Reaction score
9
Location
Ireland
Rating - 0%
0   0   0
Personally I wouldn't be overly worried. It could cause it to crack straight down from there and split on the next contact or stress. So if you can afford to replace it I would. But I wouldn't IMMEDIATELY do it.
Great understood.
Will head to my LFS and see what they have, might be a good excuse to upgrade..
 

Keeping it clean: Have you used a filter roller?

  • I currently use a filter roller.

    Votes: 41 31.1%
  • I don’t currently use a filter roller, but I have in the past.

    Votes: 4 3.0%
  • I have never used a filter roller, but I plan to in the future.

    Votes: 34 25.8%
  • I have never used a filter roller and have no plans to in the future.

    Votes: 47 35.6%
  • Other.

    Votes: 6 4.5%

New Posts

Back
Top