Has anyone created a full Raspberry Pi Aquarium monitoring/control system?

[jjduen]

i am not to prolific with nowadays with electronics, but is there anything i too can do to help?

Would you be willing to share what you have develop thus far and i can possible get some expert help to continue with the development.

 

[sebchauvour]

Bonjour Hello

Google Traduction

Lecture I2C capteur Atlas Scientific PH EC impossible

Cannot read I2C Atlas Scientific PH EC sensor


Voici le projet que je veux utiliser :

Here is the project I want to use :



https://github.com/diverjoe/FishNet/wiki


Après avoir installé tous les nodes est adapter certaine partie du programme.

After having installed all the nodes is to adapt certain part of the program.



Je n’arrive pas à comprendre comment faire pour lire les sondes PH et EC atlas Scientific.

I cannot figure out how to read the atlas Scientific PH and EC probes.


Quand je fais un I2C scan je trouve bien PH 99=0x63, EC 100=0x64, Temp 102=0x66.

When I do an I2C scan I find PH 99 = 0x63, EC 100 = 0x64, Temp 102 = 0x66.



Dans le flow, Node Edit exe node il faut rentrer une commande spéciale ????

In the flow, Node Edit exe node you have to enter a special command ????

Hardware:

Whitebox T3 | Atlas Scientific

The T3 for Raspberry Pi isolates sensors and eliminates issues with noise and ground loops that can arise using the Atlas Sensors in closed-loop systems.

atlas-scientific.com

EZO™ pH Circuit | Atlas Scientific

Atlas Scientific’s EZO-pH circuit gives engineers the ability to read pH with the same accuracy and capabilities that were traditionally only found in expensive bench-top meters.

atlas-scientific.com

EZO™ Conductivity Circuit | Atlas Scientific

The Atlas Scientific EZO-EC Circuit reads conductivity, salinity, and TDS (PPM) which are fundamental measurements of water chemistry.

atlas-scientific.com

EZO™ RTD Temperature Circuit | Atlas Scientific

The Atlas Scientific EZO-RTD Circuit makes taking high accuracy readings from a platinum RTD probes easy.

atlas-scientific.com

Je suis un peu perdu.

I am a little lost.



Merci pour votre aide. Thanks for your help.

 

[Ranjib]

Bonjour Hello

Google Traduction

Lecture I2C capteur Atlas Scientific PH EC impossible

Cannot read I2C Atlas Scientific PH EC sensor


Voici le projet que je veux utiliser :

Here is the project I want to use :



https://github.com/diverjoe/FishNet/wiki


Après avoir installé tous les nodes est adapter certaine partie du programme.

After having installed all the nodes is to adapt certain part of the program.



Je n’arrive pas à comprendre comment faire pour lire les sondes PH et EC atlas Scientific.

I cannot figure out how to read the atlas Scientific PH and EC probes.


Quand je fais un I2C scan je trouve bien PH 99=0x63, EC 100=0x64, Temp 102=0x66.

When I do an I2C scan I find PH 99 = 0x63, EC 100 = 0x64, Temp 102 = 0x66.



Dans le flow, Node Edit exe node il faut rentrer une commande spéciale ????

In the flow, Node Edit exe node you have to enter a special command ????

Hardware:

Whitebox T3 | Atlas Scientific

The T3 for Raspberry Pi isolates sensors and eliminates issues with noise and ground loops that can arise using the Atlas Sensors in closed-loop systems.

atlas-scientific.com

EZO™ pH Circuit | Atlas Scientific

Atlas Scientific’s EZO-pH circuit gives engineers the ability to read pH with the same accuracy and capabilities that were traditionally only found in expensive bench-top meters.

atlas-scientific.com

EZO™ Conductivity Circuit | Atlas Scientific

The Atlas Scientific EZO-EC Circuit reads conductivity, salinity, and TDS (PPM) which are fundamental measurements of water chemistry.

atlas-scientific.com

EZO™ RTD Temperature Circuit | Atlas Scientific

The Atlas Scientific EZO-RTD Circuit makes taking high accuracy readings from a platinum RTD probes easy.

atlas-scientific.com

Je suis un peu perdu.

I am a little lost.



Merci pour votre aide. Thanks for your help.

You have to do some configuration work on the ezo circuit to convert it from uart to i2c mode. Details are provided in their manual

 

[sebchauvour]

I have correctly configured the atlas modules in i2C

See the debug column we see them all

 

[sebchauvour]

You have to do some configuration work on the ezo circuit to convert it from uart to i2c mode. Details are provided in their manual

Bonjour Hello



Les sondes sont bien configurées en I2C

The probes are well configured in I2C

Scan I2C = 99(PH), 100(EC),102(Temp)



Je pense que le problème vient de la configuration des node exec (error :255)

I think the problem comes from the configuration of the node exec



FLOW Startup Atlas, Sensors Startup , exec node = error :255

FLOW EC Sensor Flows, EC Sensor, exec node = error :255

FLOW PH SENSOR FLOWS, PH Sensor, exec node = error :255



Edit exec node

Properties

Command "pigs" ???????



Je suis débutant sur node red.



Merci pour votre aide

 

[Bongrip420]

@fsamir that is fantastic!!!!!!!!!!!!!!!!!!!!!!!!!! it's exactly why I started this post, to see others that have done it and that are willing to share it with others....

I need more details!!! cost? availablity?

I can tell from the pics that you use a jebao dosing pump and wavemakers, this is exactly what i'm looking for!!!

Hey Rob I was looking at your gui is your code available to download I would like to take a look at it on a project similar I'm working on

 

[papimelo]

Hi Rob and DIY team here. I am trying to put together a DIY tank sensor for these key parameters (similar to the Seneye) and an associated app to monitor parameters remotely, provide alerts etc. Had a tank crash recently and it spurred me to look for options. Would love to build on whats already been done if anyone is interested in working together. Cheers!