Right on. Thanks. Never really paid attention to my PH. Always low because of CA. Reactor. No problems so far. Looks like I'll be ordering one from Geos Reef. They make one. Thanks.
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Very helpful video/thread for a first time setup. I ran a CA Rx for the first time a month ago and did not have enough demand to effectively set it. I was also under the assumption ph had to be very low to dissolve.
Going to hook it back up tomorrow and add a couple more SPS to increase demand.
Interesting thread. I have been running my Ca Rx since the summer 2012. I´m using the same method that is shown in the video. I keep my output steady on 200ml/min and only use the Ph in the reactor to adjust the Kh, Ca and Mg.
In the beginning I had some problems with the Kh demand. I couldn´t get enough out of the reactor. My tanks are heavely stocked with corals.
My reactor is build by a Fellow reefer (it has two connected chambers) and I discussed the problem with him. The issue was this: If I increased the Co2 indput to get more effect out of the reactor, it turned into gas in the top of the reactor.
He sugested that I increased the pressure inside the reactor. If the pressure increases, the Water will be able to "hold on" to the Co2 and it wont become a gas. He mentioned, that it is the same principle that is used in soft drinks or beer in cans. It releases the Co2 when you open it, because the pressure is Falling and then You get all the bubbles. It works in the same way in a Ca Rx.
I don´t use bypass because I cant get enough pressure in that way. I use a 2000L pump to feed the reactor. With a needlevalve on the output hose I can get the pressure in the reactor that I want.
My pH in the reactor is 6,22 and I never se any gas in the top of it. The Ph in the tanks is above 8, not only in the daytime. Kh in the display is 8. I´m using a "piggybag" (neutralization chamber) to use up the rest Co2. It is very powerfull. Last time i messured the output Water it was Kh 27
I have a sediment filter between the reactor output and the needlevalve to prevent any clogging. Its a sediment filter like the ones used in my RO device.
I also noticed, that treadstarter had to supply with extra Kh and a kalkstirrer to fulfill the demands of Kh.
I haven´t have any problems like that, after I increased the pressure. Well, thats not quite true. I had to refill my reactor every month to keep up.
I changed to a larger cirkulation pump to increase the virtual height in the reactor and that solved the problem. I´m now using a 3000 L pump for cirkulation.
Sorry for any misspelling or wrong grammar. I´m from Denmark and English is not my first language. But I think, that you will have less problems with the reading, than if I wrote in Danish.
Hey @ToXIc love the vid. This is the way I've been running calrx for a few years now. A few years back I finally got sick of the whole bubble drip counting method and thought to myself why can I use the acidity of the pH in the reactor to control the melt rate. For most part I got sick and tired of making sure my drip count was constant every day. Witch made me just get get rid of the ball/needle valves all together and run the effluent full stream.
One thing is key tho. I highly recommend that when controlling the co2 with a controller and a solenoid that u don't dump to much co2 in at once so that the solenoid is constantly turning on and off. I recommend that you adjust the needle valve on your co2 regulator to let the pH value drop a point every 3 to 5 minutes if longer better. I say this cause I learned first hand what could happen if u dump to much co2 to quick. 5 years ago in an old system I had a cheep regulator setup and the hammer inside solenoid got stuck in the open position. I dumped a full tank (or pretty dang close to) of co2 in one weekend. I got home from a long weekend at a concert to find every thing in my tank was dead except my sohal tang (witch I still have to this day). The pH was so low in the system that my test kits couldn't read it correctly.
Here's a pic of the tank the day after
man sorry about your loss...
nice stuff.. like the idea of ditching the output valve.. but the output proportionally dependent on the input right?
i got your point about not overdoing CO2.. it was also mentioned in the video.
man that sounds crazy thats a big ole feed pump.. any pictures? 200ml/min is alot that will cause you to be dosing too much CO2 that is doesnt get a chance to dissolve into the water and thats causing it to accumulate on to of the Rx hence the large feed pump to force water into the chambers to dissolve the CO2.
Also i could reduce the melting point off the effluent to keep up with demand but Acros love kalk its like coral crack plus it buff the ph a lil.. i like the idea of the sediment filter i'll look into that..
Been running my CaRx with this method for a good 1.5 months now. Only issue I have been having is keeping effluent output steady, with a manifold off the return, controlled by a needle valve like the one @ToXIc recommended.. Not too bad but occasionally. Still havent been able to keep alk at a steady number. Fluctuating between 8.5-10 with constant adjustments. I want 9.
So.... I found a Masterflex pump for an excellent price so I bought it. It does a max of 1440cc/hr, and adjustable. Is this going to work?
I am having the same issue with keeping the effluent steady. Feed line off the return pump and it slows down to a drop per second after a day. The line is not clogged from what I can tell.
That's a situation where a pH controller might do a better job.
Try increasing the effluent drip so the particles will pass easier trough the needle valve. But raise the ph a lil to compensate so you won't overdose and test and adjust.
I placed the needle valve on the line in side to adjust the incoming flow so the effluent line is wide open and dependent on the input. I was hoping that would prevent any blockage.